OrangePi - Revision history

Bpopp: /* Python */

2018-04-13T04:49:25Z

Python

2018-04-13T04:46:14Z

Python

← Older revision		Revision as of 04:46, 13 April 2018
Line 63:		Line 63:

	Install PIP		Install PIP
	<pre>sudo apt-get install ~~python3~~-pip</pre>		<pre>sudo apt-get install python-pip</pre>

	Install the GPIO library:		Install the GPIO library:

2018-04-13T04:46:03Z

Python

← Older revision		Revision as of 04:46, 13 April 2018
Line 59:		Line 59:

	== Python ==		== Python ==

			Follow the instructions at https://opi-gpio.readthedocs.io/en/latest/

	Install PIP		Install PIP
	<pre>sudo apt-get install python3-pip</pre>		<pre>sudo apt-get install python3-pip</pre>

	~~Follow~~ the ~~instructions at https~~:~~//opi~~-~~gpio.readthedocs~~.~~io/en/latest~~/		Install the GPIO library:

			<pre> sudo pip install --upgrade OPi.GPIO</pre>

	A simple python script to turn the flag off or on:		A simple python script to turn the flag off or on:

2018-04-13T04:44:47Z

Python

← Older revision		Revision as of 04:44, 13 April 2018
Line 64:		Line 64:

	Follow the instructions at https://opi-gpio.readthedocs.io/en/latest/		Follow the instructions at https://opi-gpio.readthedocs.io/en/latest/

			A simple python script to turn the flag off or on:

			<pre>
			import OPi.GPIO as GPIO

			GPIO.setmode(GPIO.BOARD)
			GPIO.setup(11, GPIO.OUT)
			GPIO.output(11,GPIO.HIGH)
			GPIO.cleanup()
			</pre>

2018-04-13T04:32:22Z

Using GPIO w/ Orange PI

← Older revision		Revision as of 04:32, 13 April 2018
Line 50:		Line 50:
	<pre>gpio mode 2 out</pre>		<pre>gpio mode 2 out</pre>

	~~To set the mode.~~ Once the mode is set correctly, use:		Once the mode is set correctly, use:

	<pre>gpio write 0 1</pre>		<pre>gpio write 0 1</pre>

2018-04-13T04:32:03Z

← Older revision		Revision as of 04:32, 13 April 2018
Line 46:		Line 46:
	</pre>		</pre>

	Use the table to determine the correct pin. The wPi column is the ID for the pin. ~~Use:~~		Use the table to determine the correct pin. The wPi column is the ID for the pin. For output, use the following command to change the corresponding pin's mode '''gpio mode <pin> in/out/pwm/clock/up/down/tri''':

	~~<pre>~~gpio mode <pin> in/out/pwm/clock/up/down/tri~~</pre>~~

	ie:

	<pre>gpio mode 2 out</pre>		<pre>gpio mode 2 out</pre>

2018-04-13T04:29:59Z

Using GPIO w/ Orange PI

← Older revision		Revision as of 04:29, 13 April 2018
Line 48:		Line 48:
	Use the table to determine the correct pin. The wPi column is the ID for the pin. Use:		Use the table to determine the correct pin. The wPi column is the ID for the pin. Use:

	<pre>gpio ~~set~~ mode out</pre>		<pre>gpio mode <pin> in/out/pwm/clock/up/down/tri</pre>

			ie:

			<pre>gpio mode 2 out</pre>

	To set the mode. Once the mode is set correctly, use:		To set the mode. Once the mode is set correctly, use:

2018-04-13T04:28:46Z

Using GPIO w/ Orange PI

← Older revision		Revision as of 04:28, 13 April 2018
Line 14:		Line 14:
	</pre>		</pre>

	Documentation can be found in the man pages or here: http://wiringpi.com/the-gpio-utility/.		Documentation can be found in the man pages or here: http://wiringpi.com/the-gpio-utility/. Test the tool using:

	~~And then tested~~:

	<pre>gpio readall</pre>		<pre>gpio readall</pre>

2018-04-13T04:28:30Z

← Older revision		Revision as of 04:28, 13 April 2018
Line 13:		Line 13:
	sudo ./build		sudo ./build
	</pre>		</pre>

			Documentation can be found in the man pages or here: http://wiringpi.com/the-gpio-utility/.

	And then tested:		And then tested:
Line 47:		Line 49:

	Use the table to determine the correct pin. The wPi column is the ID for the pin. Use:		Use the table to determine the correct pin. The wPi column is the ID for the pin. Use:

			<pre>gpio set mode out</pre>

			To set the mode. Once the mode is set correctly, use:

	<pre>gpio write 0 1</pre>		<pre>gpio write 0 1</pre>

2018-04-13T04:22:04Z

OrangePi Pinout

← Older revision		Revision as of 04:22, 13 April 2018
Line 1:		Line 1:
	== OrangePi Pinout ==		== OrangePi Zero Pinout ==

	[[File:OrangePiZeroPinout.jpeg]]		[[File:OrangePiZeroPinout.jpeg]]